• HOME > News > ss 304 square pipe weight char

ss 304 square pipe weight char

Calculating the weight of Pipe fittings and piping can be a daunting task, but the SS 304 square pipe weight chart is a go-to tool that makes this calculation effortless. Listed below are the various weight measurements for different types of fittings and pipes:

At the cutting edge of manufacturing, we have an impressive array of buttweld fittings – equal and reducing tees, caps and lap joint stub ends, 90 and 45 long and short radius elbows, much like bends, and concentric and eccentric reducers. If you’re searching for a way to create the perfect connection, take advantage of these advanced pieces in your setup.

A variety of flanges are available – Weld Neck, Threaded, Slip-On, Blind, Socket Weld Lap Joint, and Plate types- to meet a range of needs. The weld neck flange is designed with a long hub to allow connection between pipes with continuous welding. Threaded flanges are known for their easy installation since they join pipes by utilizing threads. Slip-on flanges slide over the outside of the pipe end before welding. Blind flanges can be used to shut off the flow of liquid or gas by covering the end of a pipe. In contrast, the socket weld flange is necessary in order to join small sizes of pipes and is commonly used with high pressures. Meanwhile Lap Joint flanges provide easy access to piping systems but do not provide any kind of support for kinetic motion systems. Last but not least, the plate flange is a flat disk offering high corrosion resistance and is often used in low pressure applications.

An extensive selection of valve types are available, such as Ball Valves, Check Valves, Butterfly Valves, Plug Valves, Gate Valves, Globe Valves, and Needle Valves, giving you ample choice when it comes to your desired system solution.

Piping is available with a nominal bore of 1/2” up to 144” in schedule 40, 80, 160, XS, and XXS.

By utilizing the following equation, we can measure and determine the mass of the various styles of fittings and tubes:

Knowing the weight of an object can be done by creating a calculation which takes into account the outer diameter of said object, as well as its wall thickness. The formula is straightforward; subtract the wall thickness from the outer diameter, then multiply that result with both the wall thickness and 10.69 to gain an accurate estimation of its weight in pounds.

The OD (Outside Diameter) is the headline of the article, yet the key detail for consideration is the Wall Thickness – the girth of the pipe.

The SS 304 square pipe weight chart provides the essential heft associated with any planned piping task. This data set allows you to rapidly discern the exact weight of the desired pipe or fitting, allowing you to move forward with your project without any delays.

Related Product


Warning: Use of undefined constant rand - assumed 'rand' (this will throw an Error in a future version of PHP) in /www/wwwroot/www.ytdrtube.com/wp-content/themes/msk5/single.php on line 77
  • Black Rectangular Hollow Section

    Black Rectangular Hollow Section

    OD(MM) THICKNESS(MM) OD(MM) THICKNESS(MM) OD(MM) THICKNESS(MM) OD(MM) THICKNESS(MM) 20*20 1.3 60*120 80*100 90*90 1.50 180*180 3 300*800 400*700 550*550 500*600 1.4 1.70 3.5-3.75 9 […]

  • Hot Dip Galvanized Rectangular Hollow Section

    Hot Dip Galvanized Rectangular Hollow Section

    Iron and steel materials are indispensable resources in human life today. However, due to its own characteristics, “corrosion is accompanied by us every day and consumes our […]

  • Black Square Steel Tube

    Black Square Steel Tube

    SPECIFICATION TABLE OF BLACK SQUARE STEEL TUBE OD(MM) THICKNESS(MM) OD(MM) THICKNESS(MM) OD(MM) THICKNESS(MM) OD(MM) THICKNESS(MM) 20*20 1.3 60*120 80*100 90*90 1.50 180*180 3 300* […]

  • Pre Galvanzied Square Steel Tube

    Pre Galvanzied Square Steel Tube

    1.Introduction of pre-square tube Coiled pipes are pipes and pipes for processing technological processes, and are the name of general pipes, which are pipes made of long steel coi […]

  • EN10210 EN10219 Black Carbon Steel Welded Square Pipe

    EN10210 EN10219 Black Carbon Steel Welded Square Pipe

    Yuantai Derun Steel Pipe Manufacturing Group is a steel pipe and steel enterprise that has operated for many years, mainly engaged in steel products such as black square and rectan […]

  • Hot Dip Galvanized Square Steel Pipe HDG Tube

    Hot Dip Galvanized Square Steel Pipe HDG Tube

    Thickness: 0.5- 60 mm OD(outer diameter): square 10*10-1000*1000mm rectangular:10*15-800*1100mm Section Shape: Square OR rectangular Place of Origin: Tianjin, China Application Str […]

  • Square Steel Pipe Carbon Steel Pipe

    Square Steel Pipe Carbon Steel Pipe

    Thickness 0.5- 60 mm Tolerance as required OD(outer diameter) square 10*10-1000*1000mm rectangular Brand YUANTAI DERUN Section Shape Square OR rectangular Length 3-12M according to […]

  • Square Hollow Section

    Square Hollow Section

    Thickness: 0.5- 60 mm OD(outer diameter): square 10*10-1000*1000mm rectangular:10*15-800*1100mm Section Shape: Square OR rectangular Place of Origin: Tianjin, China Application Str […]

  • Square Seamless Steel Pipe

    Square Seamless Steel Pipe

    Attribute parameters of seamless square steel tubes Thickness  3- 50 mm Tolerance  as required OD(outer diameter)  100*100-800*800 Brand  YUANTAI DERUN Section Shape  Square OR rec […]


  • Post time: 2023-07-03